Відео

What yr chevy springs can you upgrade to?

Super helpful. Thanks a lot!

Very clear instructions; UA-cam at it's best. Thank you.

Just my opinion but no way was that the first time that bead was broken, that's not how the come off.

Good work

Nice truck

I had been searching for a video to show me just this hookup. I went through countless videos, and I found yours which was very helpful. Thanks, my man for your help.

Thanks you very much, it help me a lot

I did this adjustment i do have an LE model 1991 D350 with cruise control. Shifts much better now. I also added an inch block under the gas petal, is a common fix for more throttle control. The issue im having is i get to about 70 MPH or about 112 KPH. and i can not press my petal any past that if i hold it fully depressed it will slowly climb in speed. Is this factory settting for these trucks? Also im hitting about 2200 rpm max. Any suggestions would be appreciated! Great videos btw love the camper vids!

Hey , I've read that if you only have 1 tire off the ground and can spin it at all then your clutches are shot. what you think?

Would you happen to know how to get the weather seals on the electric motor cause mine are just non existents

The Oven’s “pre-heat” digital gauge set.

Tyler, question for you. Very intermittent problem, spedo and OD will not function. Driven 1km to 70km then the spdo and OD kick in again. Normally this will only happen when well below zero. The onoff onoffon test shows no faults. The heat/water lights function normally. I was wondering if I had a poor ground on the tranny. Love my truck! People keep trying to buy it in the Princess parking lot.

Thanks again, mine were all clogged. 1985 F250. AK

Nice 🤙🏼

Keep it going!

Where did you get the new hoses coming from reservoir

Nice work and nice welder!

Hey Tyler, I stumbled across your channel about a year ago and it’s become one of the first places I go to when I don’t entirely know what I’m doing when repairing certain things on my 1992 dodge w250. I skimmed through your videos and couldn’t find for myself so I hoped I could just ask. Do you have anything regarding engine mounts for our first gens?

Sweet, gonna do this today 👍

I wonder if it is permissible to connect to multiple V+ or multiple V-, and if this helps with current capacity. I used to run a company designing switchers, and I can tell you that it depends on the detail of the design. Sometimes it is bad, sometimes it is OK. Nothing I have found online answers if it is OK with these Bosytro supplies. Unless I can find something assuring me that it is OK, I will connect to just one pair.

What workshop book is that and where did you get it?

Great video, Tyler. I really enjoy your detail and clear explanations. Gonna send you an email about this, as I'm thinking of upgrading my turbo as well.

Would that leak on to manifold small drips ?? On x5 2011

could you please tell me the brand and model of you temp gun??? thanks

That part at napa is a 4 pin relay, the starter is a 5 pin

I had to park my 1993 W350 1st gen Cummins because the front rear shackle mounts rusted off. The frame on the truck is otherwise solid still so I'd like to get her fixed. Do you know if Hogback Fabrication makes a kit like that for the rear?

I’ve been chasing these problems way too long. You the man!

Question... I am getting ready to do this upgrade, but I live in the south. So I need my ac to be on point. If I were to do the same install but mount the ac condenser on the front, would I be able to push the intercooler back the same thickness as the condenser? Do you think it would still fit with the grill not rubbing?

do you have the same lift on all three trucks?

Did you have to bleed the hydraulic clutch. If so how did you go about that?

Prob took you 30 min to put that O ring inside the cylinder

please share the music you used

Big bump stick, it's got that rump, rump, rump to it ! Sounds GREAT !

It should work on a 4x4 d250 shouldn’t it ?

Thanks for a great video. The BMW dealer here is a total ripoff artist. They charged my wife $202 (parts & labor) to replace the air filter in our ‘16 X5/35d. It’s a 5-minute job. They also charged over $280 for oil & filter and top off the DEF. next time I’ll do it myself and be happy to keep about $375 of that.

how's your getrag holding up? has it been rebuilt? mines getting fussy in 3rd

Eh... i already have the dash mostly apart... might as well 😂😂 stupid brittle vacuum lines caused me to be there anyway

Hey Tyler, Any idea what size the yolk nut on the front of the T case is? Thanks

Man, I wish it was that easy to get past that key....what did you mean by just putting your screwdriver in to line it up

Thanks for the simple and detailed video. Both the doors on a 86 D150 I bought this year sag badly. It will be good to be able to shut and lock the doors. Such a cheap fix.

Its good that you got ALL of that potting compound out. More than likely it was much lighter in color when it was new. It looks like old Sony bond which becomes conducive and corrosive with time.

Im saving this video for future reference cause the only problems I had with my 1st gen are , dead short to ground in power feed to trans , fried ignition switch and i had to clean up the main disconnect plug on the battery cable coming out of the alternator.

What a clean truck!

When you rebuild thr jack posts can you make a video. I have the same ones and they need some love

Hey, that’s awesome! Need to do the same thing for my old skid steer that doesn’t have any analogue gauges. Have you posted the code and a schematic anywhere online?

i know its a an old video but its precicly what im trying to achive on my truck, but if your still around i have a question about your temperature sender is it just a standard 12/24volt sensor? its all i can find in that form factor and am i safe to assume sending 5 volts to it it should work just fine as ill still be plotting just the resistance change even though the sensor is rated for 12volts?

Bro you just saved me so much time when you said the one switch wasn’t clicking the same I knew mine was doing the same thing and I don’t have to tear everything apart now

Worthless video. You don't actually show how to do any of the steps.

I just bought a 2016 X5 M package, is it the same procedure?